Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Gora Arasar
Country: Gabon
Language: English (Spanish)
Genre: Photos
Published (Last): 24 May 2016
Pages: 249
PDF File Size: 19.84 Mb
ePub File Size: 6.64 Mb
ISBN: 922-3-37338-288-7
Downloads: 22215
Price: Free* [*Free Regsitration Required]
Uploader: Akikora

Press the Enter key on your keyboard. Wait for the Run LED to stop flashing.

This decal enables you to enter wiring and connection details and identifies the location and designation of cable connections, LEDs, etc.

Controller will reject WWW connections. Set switch 2 to OFF open.

Gallagher Controllers | AES Group Ltd.

These contacts close when the Controller is powered up, and remain closed until either the power is removed or there is a ‘Catastrophic Failure’. The Settings in bold specify the default new installation startup configuration.

The Enter Network Password screen displays. Cardax FT Version 5. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

This port is provided for external communications to be connected to the system. Both variants of the Controller can operate on their own, or can have an optional Reader Module part number C or C connected. The differences between the two variants are shown in the following table: Cardax Ft Controller pdf Download Report.

  LIVRO UMA LONGA JORNADA NICHOLAS SPARKS PDF

The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets: Set switch 2 to ON closed. Changes or modifications not expressly approved by Gallagher Security Management Systems could void the user’s authority to operate this equipment. The In-service relay is used to signal an external alarm if the Controller fails. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Open the Internet Browser. Boot code monitor running. Ensure both you and the equipment are earthed before beginning any servicing.!

Cardax Ft Controller 6000pdf

However, this DC voltage out will be approximately 1 volt lower than the voltage supplied to the Cardax FT Controller An upgrade of the Controller software via a USB memory stick is complete and the USB drive must be removed for installation to complete. The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center.

A dial-up modem may be used for communication if network communications are not available. Cardax FT for Airport Security. The software is powerful, Following full antistatic precautions, disconnect all cables from the Cardax FT Controller Carda on power to the Cardax FT Controller The Cabinet door must remain closed for at least one minute for the initialisation of the 600 tamper detectors to be completed.

  GIANCARLO CATALDO ROMANZO CRIMINALE PDF

Alternatively, an override reset on the Controller can be carried out in Cardax FT Command Centre via the Status and Overrides tab of the Controller properties with the cabinet closed.

In the event of a catastrophic failure, after approximately 60 seconds the In-Service relay opens. Providing flexible configuration options to meet specific site ccardax, Gallagher Controllers:. These limits are designed to cardxa reasonable protection against harmful interference when the equipment is operated in a commercial environment.

The cabling between GBUS devices should be done in a daisy chain or serial format, i. Assigning an IP address manually via a web browser When the Cardax FT Controller is started reset or power-up with DIP switches 2 and 3 enabled, the Controller uses the following carax addresses: There is a proprietary serial communication protocol between the two boards. The following initialisation procedures are detailed in the later section titled “Initialisation”: