BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.

Author: Togal Doukree
Country: Slovenia
Language: English (Spanish)
Genre: Music
Published (Last): 10 August 2015
Pages: 102
PDF File Size: 5.42 Mb
ePub File Size: 15.20 Mb
ISBN: 503-4-35191-348-9
Downloads: 74630
Price: Free* [*Free Regsitration Required]
Uploader: Akimuro

See diagram for details. Different input configurations result in slightly different noise readings. All SST amplifiers are convection cooled. Stripped bare wire up to 3 gage can be inserted through the hole in the binding post and held in place by tightening the post knob.

Balanced systems provide noise rejection from external electrical interference, so cable length can be very long 50m kanual longer.

Note that copper wire is malleable and may require further tightening after the initial installation. Check that the voltage rating on the label conforms with your locality. Unrestricted air-flow across its heat sinks is a must. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston. Master circuit – breaker. This is the home theatre setting for balanced operation Or use this bdyston with any systems where the volume control rotation is limited to the bottom half of the control or less.

The SST amplifier uses a magnetic-trip circuit breaker brysron to protect the amplifier. Tampering by persons other than factory authorized service personnel, or failure to fully comply with Bryston operating instructions, voids the warranty. When the power supplies have stabilized the channel will come out of mute and the Swt will change to green normal operation.

  ASSIMIL ARABE SIN ESFUERZO PDF

Banana plugs offer a quick disconnect option.

Bryston 4B SST C Manuals

When the channel has cooled to a safe operating condition the channel will return to normal operation. The voltage is listed on the label found at the upper right of the bryson panel. The speaker binding posts will accept wire up to 3 gage in size. The balanced input requires a balanced pre-amp source. Also see installation section on ventilation.

Bryston 4BSST User Manual | 8 pages | Also for: 3BSST

Input Sensitivity Gain Switch. Heat Dissipation 8 ohms – Bridged W 8 ohms Max. Should your instillation conditions be constricted, then additional forced air-cooling may be necessary.

The above noise ratings represent minimum readings, actual readings may be better. Combinations may be used when bi-wiring. In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance.

The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source.

Then power the unit up normally. For this reason do not install anything directly above it. Each channel selects wst balanced or single ended input. Should thermal shutdown occur, the channel will mute, and the channel LED will turn orange indicating this condition. Never lift the safety ground to the amplifier nor remove the ground pin from the plug. Balanced input Vs Single ended input: Before inserting a banana plug into the binding post be sure to tighten the post nut to avoid rattling and to provide full insertion of the banana plug.

  AMPLI BOSE DXA 2120 PDF

Persistent Bryzton shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink. Bridge mode is for mono operation.

Bryston 4BSST User Manual

The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. Cables bryshon be dressed away from input and power cables. This is the home theatre setting for single ended or un-balanced operation.

It’s a community-based project which helps to repair anything.

This will ensure the amplifier is protected in future transport. Do not over tighten or the binding post may become damaged.

Clipping flashing red Clipping occurs when the channel output level no longer can follow the level increase at the input Overdriven input condition. Lugs should be gold plated. Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. The brydton will now power-up only when the control voltage is present on. Push again and the amplifier will power-down.

Installation see rack mounting section if applicable Ventilation. Gold plated spade lugs are available from Bryston. The power up or turn-on of the 3B SST may be activated sts remote control voltage.

Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application.